I have a problem with newcs and MTV channels

[sweex123]

Hello I have a problem with newcs and MTV channels
when I get into an original receiver, I immediately stop signal
but I put him back in the server 10 minutes black again
what should I do or change in my config
I see my config
I have a linux PC with a Smargo

************************************************** ********
<?xml version="1.0"?>

<newCSconfig>
<readers name="Canal">
<device>
<name>Cardreader</name>
<type>smartreader+</type>
<node>/dev/ttyUSB0</node>
<mhz>357</mhz>
<parity>even</parity>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>no</blocksa>
<blockua>no</blockua>
<blockga>no</blockga>
<blockC0>Yes</blockC0> # nieuw er tussen gevoegd
<boxid></boxid>
<PTShandshake>no</PTShandshake>
<Seca-PPV>no</Seca-PPV>
<crypto-special>no</crypto-special>
<carddetect>no</carddetect>
<newcamd_port>15000</newcamd_port>
<autosid>no</autosid> # stond op yes nu weer op no
<priority>round</priority>
</device>
</readers>

<cache>
<emm>10</emm>
<ecm>10</ecm>
</cache>

<debug>
<mode>advanced</mode>
<level>normal</level>
<type>init</type>
<output>all</output>
<udp_host>192.168.1.10</udp_host>
<udp_port>1000</udp_port>
<tcp_port>3001</tcp_port>
<tcp_options>normal,init</tcp_options>
</debug>

<newcamdserver>
<enabled>yes</enabled>
<deskey>11 22 33 44 55 66 77 88 99 10 11 12 13 14</deskey>
<name>Canaldigitaal</name>
<user>
<name>local</name>
<password>local</password>
<au>on</au>
</user>
<user>
<name>Bert800</name>
<password>Bert800</password>
<au>on</au>
</user>
<user>
<name>Bert500</name>
<password>Bert500</password>
<au>on</au>
</user>
</newcamdserver>
</newCSconfig>

[moreincubus]

Hi, I have the same problem.
All channels work except for a few (eg. some MTV, sport1 maybe more) which show up as scrambled.
When I use MultiCAS, these channels are decoded, back to newcs-> these channels are not decoded.
which version of newcs do you use? I use 1.20.

<?xml version="1.0"?>
<newCSconfig>
<readers name="Card Readers">
<device>
<name>upper</name>
<type>azbox</type>
<node>/dev/scard</node>
<export>yes</export>
<enabled>yes</enabled>
<parity>odd</parity>
<reset>normal</reset>
<blocksa>no</blocksa>
<blockua>no</blockua>
<blockga>No</blockga>
<newcamd_port>12024</newcamd_port>
<autosid>no</autosid>
<carddetect>yes</carddetect>
<priority>hard</priority>
<PTShandshake>no</PTShandshake>
<mhz>357</mhz>
<boxkey></boxkey>
<rsa>key</rsa>
</device>
</readers>

[moreincubus]

I think i solved it by upgrade newcs via the remote.
after this i changed the config file to my liking again.